Skamol Lime Mortar

1. Remove loose plaster, tar, paint residue and organic materials from the wall. In case of mold growth, clean the wall with a biocidal product.
   
   
2. Make sure the wall is level. Several layers of Skamol Adhesive can be applied with a thickness of 10mm to level the surface of the wall. Each layer must harden before a new layer of adhesive is applied.
   
   
3. Use water or Skamol Primer to ensure the wall surface is free of dust.
   
   
4. Remove dust from the side of the SkamoWall Board facing the wall.
   
   
5. Apply Skamol Primer to the side of the SkamoWall Board facing the wall. There is no difference in the function of the two sides of the SkamoWall Board, so it does not matter which side of the SkamoWall Board is mounted facing the room.
   
   
6. Wait approx. 30 minutes for Skamol Primer to dry.
   
   
7. Mix Skamol Lime Mortar at a ratio of approx. 4.5L of clean water per 20kg bag:
   
   • Pour 2.5L of water into a mixing bucket
   • Add the entire contents of the Skamol Lime Mortar bag while stirring vigorously
   • Add the remaining 2L of water to the mixture until achieving the desired consistency
   • Stir the mixture vigorously for about 7 minutes
   • Let the mixture rest for about 2 minutes and stir again for about 1 minute
   • After mixing, Skamol Lime Mortar can be used for approx. 2 hours
     
     
8. Apply Skamol Lime Mortar to the wall in an even layer with an 8mm notched trowel. We also recommend to apply Skamol Lime Mortar to the surface of the side of SkamoWall Board facing the wall in an even layer with an 8mm notched trowel. The total layer of Skamol Lime Mortar should be between 4mm and 10mm.
   
   
9. Place the SkamoWall Board approx. 10cm from the desired location.
   
   
10. Immediately push the SkamoWall Board into place to level out the Skamol Lime Mortar. SkamoWall Board must be fully bonded to the Skamol Lime Mortar, leaving a 5mm gap between SkamoWall Board and the floor. The gap may be filled with an inorganic elastic material such as self-adhesive foam or silicone.

If Skamol Lime Mortar is used as a plaster, follow these instructions

1. Remove dust from the surface of the mounted SkamoWall Board.
   
   
2. Apply Skamol Primer to the surface of the mounted SkamoWall Board.
   
   
3. Wait approx. 30 minutes for Skamol Primer to dry.
   
   
4. Mix Skamol Lime Mortar at a ratio of approx. 4.5L of clean water per 20kg bag:
   • Pour 2.5L of water into a mixing bucket.
   • Add the entire contents of the Skamol Lime Mortar bag while stirring vigorously.
   • Add the remaining 2.0L of water to the mixture until the desired consistency is achieved.
   • Stir the mixture vigorously for about 7 minutes.
   • Let the mixture rest for about 2 minutes and then stir again for about 1 minute.
   • After mixing, Skamol Lime Mortar can be used for approx. 2 hours.
     
     
5. Apply Skamol Lime Mortar in an even thickness of 2mm to 3mm.
   
   
6. Level and felt the Skamol Lime Mortar.
   
   
7. If the hardened Skamol Lime Mortar is uneven, water, apply and felt Skamol Lime Mortar in a thickness of 2mm to 3mm. This can be repeated until the desired surface is achieved.

 

Find out more about mounting here.

Brochure

Mounting instructions

Data sheet

Safety data sheet (SDS)

Bag contents

20kg

 

Size of bag

600 × 300 × 100mm

 

Yield

2.5m² as an adhesive (7mm)

7m² as plaster (2mm)

 

Storage

Store in a cool and frostproof place.

 

Contains

• Lime (chemical)
• Hydraulic
• Calcium hydroxide

UFI-kode HXMJ-PYQ4-JF0U-CQ2Q

• Causes skin irritation.
• Causes serious eye damage.
• If medical advice is needed, have product container or label at hand.
• Keep out of reach of children.
• Wear protective gloves/protective clothing/eye protection/face protection.
• If in eyes:
  • Rinse cautiously with water for several minutes.
  • Remove contact lenses, if present and easy to do.
  • Continue rinsing.
  • Immediately call a poison center/doctor.
• Dispose of Skamol Lime Mortar in accordance with local regulations.